System K2 - Factory Swaged Rigging Screw (x2) Slimline Balustrade System

System K2 - Factory Swaged Rigging Screw (x2) Slimline Balustrade System

The Rigging Screw x2 Slimline Balustrade System is an elegant looking stainless steel balustrade with an external slimline tensioner fitted to each end of the wires.  This system is designed for fitting to timber posts via included Lag Eye Screws. Alternately, this system can be fitted to metal posts via Small Eye Screws fitted into Blind Rivet Nuts installed into the metal posts.

Enter the total number of System K2 wires required and add to cart.  By using Quickshop, you can add the things you need without leaving this page.

Calculate the total length in whole metres of wire rope required (number of wires per run x total length of all runs).

Add any other accessories you need (eg lag screw driver tool and rigging screw spanner).

You'll need to send us a separate email with your required run lengths, for example:

3250 x 11, 4146 x 11, 2545 x 11 - which means:

11 wires @ 3250mm, 11 wires @ 4146mm, and 11 wires @ 2545mm

Note all measurements should be inside post to inside post, with stairs measured the same way but parallel to the handrail.

Installation is the same as for System K, except that there is a rigging screw at both ends instead of a single rigging screw and fork terminal.

Balustrade System K2 - Balustrade Wires with 2 x Rigging Screws

Balustrade System K2 - Balustrade Wires with 2 x Rigging Screws

$19.50

The Rigging Screw and Fork Terminal Slimline Balustrade System (System K2) is used with our most popular (system K) balustrade kit, where there are...

View full details
$19.50
3.2mm S316 Stainless Rope 1 x 19 Construction - cut length per metre

3.2mm S316 Stainless Rope 1 x 19 Construction - cut length per metre

$1.44

AISI 316 (marine grade) stainless steel premium quality wire rope. Made with diamond coated dies and heat annealed, this stainless steel cable is e...

View full details
$1.44
Socket for driving M6 lag eye screw into timber (Nickel Plated). Not suitable for Impact Drivers

Socket for driving M6 lag eye screw into timber (Nickel Plated). Not suitable for Impact Drivers

$6.12

Socket for driving M6 lag eye screw into timber (Nickel Plated). Not suitable for Impact Drivers

$6.12
C-Spanner Tightening Tool for M5 Rigging Screw

C-Spanner Tightening Tool for M5 Rigging Screw

$6.12

Electro-polished stainless steel C-Spanner tightening tool for easy tightening of rigging screw bodies (bottle-screws).

$6.12
Nylon Grommet Split Type, Black, 9mm O.D. x 10mm long, suits wire rope 3.2-5.0mm

Nylon Grommet Split Type, Black, 9mm O.D. x 10mm long, suits wire rope 3.2-5.0mm

$0.54

Used for protecting aluminium or steel posts against chafing or electrolysis with stainless balustrade wire. Black grommets enhance the appearance ...

View full details
$0.54
35° Angled Nylon Grommet for stairs. Two Piece, Black

35° Angled Nylon Grommet for stairs. Two Piece, Black

$1.20

Used for protecting aluminium or steel posts against chafing or electrolysis with stainless balustrade wire. Installation for angled grommets requi...

View full details
$1.20

You recently viewed

Clear recently viewed